M01Natural Oak VeneerMDF Premium A/B
Factory matt lacquered, 6 m²Custom joinery specification software
Give every drawing the detail behind it.
Custom joinery specification software helps you keep technical drawings, materials, hardware, dimensions and fabrication notes together, then issue the whole joinery package as one contractor pack.
ONE JOINERY RECORD
Keep the drawing and the specification together.
Upload the drawings produced in your drafting software, then keep the design intent, construction information and supporting specification around the same joinery item.
J-01-01ENTRY WARDROBE, ELEVATIONR01
DESIGN INTENTFlush fronts, continuous vertical grainAttached to J-01
DESIGN INTENT
Record what the drawing alone cannot explain.
Capture the visual and construction intent behind the joinery so the contractor understands both the geometry and what matters in the finished result.
Entry Wardrobe
Built in entry wardrobe
DESIGN INTENT NOTESCreate a full height entry wardrobe that reads as an integrated architectural element rather than freestanding furniture.
Maintain continuous vertical grain and concealed detailing throughout.
- Room
- Entrance
- Type
- Wardrobe
- Status
- Design Development
- Fabricator
- Not assigned
WIDTH2465 mmDEPTH600 mmHEIGHT2400 mm
- Door style
- Flush slab fronts
- Opening
- Integrated vertical pull
- Grain direction
- Vertical
- Edge detail
- Matching natural oak edge banding
- Shadow gap
- 5 mm
- Plinth
- Recessed, concealed
- Interior finish
- Matching natural oak veneer
Put repeatable construction decisions into fields, not scattered drawing notes.
DRAWING REGISTER
Keep every joinery sheet attached to the item it describes.
Upload plans, elevations, sections, details, renders or reference sheets without separating them from the joinery specification.
MATERIALS + HARDWARE
Specify the parts the drawing does not show clearly enough.
Keep substrates, finishes, hinges, runners, handles, rails and supports attached to the joinery package.
Materials and components stay structured, measurable and linked to the same item as the drawing.
M01Natural Oak Veneer
M04Mirror6 mm clear, silvered
1 pc
M07Calacatta Vagli MarbleHoned stone
1.5 m²J-01-01ENTRY WARDROBE, ELEVATIONR01
M01Oak veneerM04MirrorM07Marble seat
MODULES
Describe the internal layout without drawing another sheet for every instruction.
Record module sizes and configuration notes directly against the joinery item when a structured instruction is clearer than another annotation.
J-01-01ENTRY WARDROBE, ELEVATIONR01
Hanging rail, one fixed shelf and three adjustable shelves.
DIMENSIONS
Keep the critical dimensions easy to find.
Record key fabrication dimensions as searchable structured values instead of burying every important measurement inside a drawing.
Move across the values to see which area of the wardrobe each dimension describes.
J-01-01ENTRY WARDROBE, ELEVATIONR01
depthStored as a searchable value against the joinery item.
FABRICATION DETAILS
Put the fabrication instructions where they cannot be missed.
Record the installation, material and workmanship requirements that are too important to leave as scattered notes across drawings.
Veneer grain alignment
All visible door fronts use vertical grain. Sequence match adjacent panels where possible and maintain grain continuity across the composition.
Not every fabrication instruction belongs on the drawing.
Drawing
Shows geometry.
DetailsExplain how it should be built.
CoordinationExplains what must happen around it.
COORDINATION
Record what has to happen before fabrication and installation.
Keep site, electrical, plumbing, HVAC, appliance or building interface requirements attached to the joinery item.
- Discipline
- Building interface
- Requirement
- Final Site Dimensions Before Fabrication
- Location
- Entire Wardrobe, Wall to Wall, Floor to Ceiling
Verify the finished opening after wall, floor and ceiling finishes are complete.
Confirm 2465 W × 600 D × 2400 H mm design dimensions and record any irregularities before production.
Fabricate from verified site dimensions only.QUANTITIES
Turn the specification into a measurable schedule.
Keep material and hardware quantities visible alongside the joinery record so the pack carries more than geometry.
CONTRACTOR PACK
Turn the joinery record into one contractor ready pack.
Bring drawings, material schedules, hardware, dimensions and technical instructions together in one structured PDF.
Contractor Joinery Pack
01Overview and design intent
02Technical drawings
03Materials and finishes
04Hardware
05Modules and dimensions
06Technical details
07Coordination requirements
08Quantities
2465 × 600 × 2400 mm
M01Natural oak veneer6 m²
M046 mm mirror1 pc
M07Calacatta marble1.5 m²
H01Long handle3 pcs
H02Concealed hinge15 pcs
J-01-01ENTRY WARDROBE, ELEVATIONR01
THE COMPLETE RECORD
The contractor should not have to reverse engineer the design from a drawing.
Keep the geometry, materials, components and instructions together so the fabrication information is easier to find and easier to issue.
DRAWINGSMATERIALSHARDWAREDIMENSIONSDETAILSCOORDINATIONCONTRACTOR JOINERY PACK
CUSTOM JOINERY
Keep every detail with the drawing.
Bring drawings, materials, hardware and fabrication information together before issuing the contractor pack.
2465 × 600 × 2400 mm
5 drawings7 materials6 hardware items12 technical details